#10 Blue Steel Dog Clipper Blade (1.5 mm)

The Blue Steel #10 clips a close, even 1.5mm coat and runs a SuperZirconia ceramic cutter as its moving edge. Ceramic is far harder than steel, so the cutter takes a keener edge, glides through the coat, and stays sharp long after a steel cutter would have dulled. It runs cool through the longest sessions too, which keeps the dog comfortable and is kind to warm, sensitive skin.

• A SuperZirconia ceramic cutter, harder and sharper than steel, for a clean and even 1.5mm cut
• Runs cool through long sessions, gentle on warm, sensitive skin and easier on an anxious dog
• Holds a keen edge far longer than a steel cutter, so it dulls and wears down much more slowly
• Pre sharpened and ready to work, powering through thick coats and reaching feet, face and sanitary areas
• Rust free ceramic that wipes clean in seconds

It fits Andis, Oster, Heiniger and every other A5 clipper. Whether you groom back to back all day or keep one much loved dog looking its best at home, the Blue Steel #10 gives you a cooler, sharper cut that lasts.

A little preparation makes clipping smoother and helps your blade do its best work.

1. Start with a clean, dry coat. Brush out loose hair and gently comb through tangles first. Do not force a blade through tight mats; ask a professional groomer for help if the coat is matted close to the skin.
2. Choose the finish before you start. This #10 blade leaves approximately 1.5 mm. Coat texture, preparation and clipping direction affect the finished look. If you are unsure, start with a longer length and test a small area.
3. Let the blade glide. Use light pressure and smooth, overlapping passes with the flat of the blade against the coat. Stop if it drags or pulls instead of pushing harder.
4. Keep checking comfort. Check blade temperature frequently and pause or change to a cool blade when needed. Give the dog a break if they become restless or uncomfortable.

Not sure which length suits your next groom? Try the Grooming Adviser or ask the VUNRO team before you buy.

1. Clear away hair and debris. Switch the clipper off before removing the blade or brushing it clean. Clean both the teeth and the back of the blade with a soft blade brush.
2. Oil regularly. Use clipper-blade oil at the contact points, following the clipper and oil instructions. Wipe away excess before clipping. Cooling spray is not a substitute for proper oiling.
3. Watch the temperature. Every blade can warm up in use. Check it regularly and allow it to cool, or swap to a spare, before continuing.
4. Clean after each groom. Use a suitable blade cleaner or disinfectant as directed, including its contact time. Remove residue, dry thoroughly and re-oil before storing.
5. Protect the teeth in storage. Keep the blade dry and protected from knocks. Do not use a blade with chipped or damaged teeth.

If a clean, oiled blade still pulls, stop and check that it is fitted correctly. The cutter or your clipper's blade drive may need attention. Contact us for help choosing the right replacement instead of guessing.

Will this blade fit my clipper?

It fits a compatible detachable A5 clipper. A5 blades do not fit VUNRO D-Series clippers or the FlexFit PRO, MaxFit PRO and PawTrim blade systems. Check your model in our blade compatibility guide, or send us the model name if you are unsure.

How much coat does this blade leave?

The #10 is rated at 1.5 mm. That is a guide to the finish, not a promise that every coat will look identical. Clipping against the coat's growth generally gives a closer result than clipping with it.

Can I use a guard comb over it?

Only use a guard comb with a blade number and width approved for that set. Not every A5 blade is suitable underneath a guard comb; check the set's compatibility before ordering.

Why is my blade pulling or leaving lines?

Check for tangles, trapped hair, a dry blade or an incorrect fit first. Clean and oil it, check the temperature, and use light, even passes. If the problem continues, stop and ask us for advice; pressing harder can make it worse.

Can I replace the cutter without replacing the whole blade?

Replacement cutters are available for A5 blades. Match the cutter to the blade's size, width and type: standard, wide and skip-tooth cutters are not all interchangeable. Ask us to check the match if you need a hand.

How do I buy several blades together?

When a bundle offer is available on this page, use “Choose your blades & save” near the Add to cart button. Select the blades you want in the bundle section and check the displayed total and offer terms before adding the bundle to your cart.